9 Simple Steps to Waterproofing Exterior Walls

“Your walls form the foundation of your home. The weather out there will not be good for your house’s exterior walls, so you need to pay special attention to them. It’s not enough to paint the wall. After dealing with rain, snow, wind, dust, and heat, the paint will start peeling off.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

A lot of dust and dirt is carried by air and sticks onto the outer part of the wall. To make sure the process is efficient, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned by using a broom, brush, or sandpaper. Then use a power washer to wash it off.

Step 3: Check out for the cracks and fill them up

Cracks and holes can be found over time on your exterior walls. Follow up the cleaning process with a thorough finding of all the cracks and holes on the wall to ensure proper weatherproofing. Then fill them with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The cement mixture can penetrate inside the cracks. Make sure to remove the loose cement from the wall before you apply the cement.

Step 4: Add a layer of cement waterproofing sealer

To make sure your wall is waterproof, you need to apply the cement waterproofer. After applying the cement in the crevices, let it dry, then apply the waterproof paint seal for the exterior walls. Allow it to be dry.

Step 5: Pick the right water-proofer

“There are a lot of waterproof products in the market. It’s important to pick the right one for the wall. Pick the water-proofer based on whether the wall is concrete or silicate.”

You can choose between a silicate-based concrete seal or a concrete coating. Pick a plaster waterproof Additive to strengthen your walls.

Step 6: Apply the water-proofer

Use a brush or roller to apply the water-proofer to the walls. Give a thin coat first if you want to apply more than one layer. Let the first coating dry before adding the second one.

Step 7: Apply tar and heavy-duty membrane

If you want to add more strength to the layers, you need to use a tar-based pitch after the drying of the cement. You can apply it on your wall.

After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of your walls

Step 8: Consider adding gravel

If you want to lay the drainage pipes, you need a proper base below the footer. The drainage pipes will get adequate support from a 34-inch gravel base. Gravel is long-lasting and provides enhanced protection.

You have to lay the drainage pipe-cover along with the gravel. Go near the footer and level the gravel. A covering for the pipe should be at least 3-inches.

Step 9: Add a fabric barrier

Wrap the pipe with a fabric barrier. Ensuring a fabric barrier is going to prevent the formation of dirt and keep your system clean. Then build the top of the dirt relatively high and allow it to settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia is

Conclusion:

Good waterproof gives your home a new life and strength to deal with weather-related issues. Magicrete can help you with good waterproof solutions for your walls. At a very low and affordable price, Magicrete has quality service.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like”